Potterton Paramount four Installation Manual Download Page 129

Page: 129 / 144

10.1.3 Protection against contact

Danger of electric shock

Danger to life due by missing shock-proof protection.

To ensure shock-proof protection, all parts of the boiler to be

screwed on – the casing parts in particular – must be screwed on

correctly after work has been completed.

10.1.4 Approved detergents

Cleaned heat exchangers improve heat transfer and save energy. The fol

lowing detergents have been tested and approved by Potterton

Commercial for cleaning heat exchangers:

Sanit Care Aluminium-Wärmetauscher Spezialreiniger

Sotin 240 Heizkesselreiniger

Danger

Cleaning agents for aluminium heat exchangers are irritants

and/or corrosive.

Before starting work the corresponding security and safety meas

ures of the manufacturer must be observed. In addition the in

structions for use and transport printed on the packaging and con

tainer must be observed.

See

The Potterton Commercial maintenance instructions must be ob

served.

Note

The safety data sheets for the detergents listed are included with

the product or are available from the respective manufacturers.

Caution

During application of the detergent only the heat exchanger on the

flue gas side may be treated. No detergent residue may remain on

the boiler components, the cable plugs or casing, since this can

otherwise lead to corrosion and appliance malfunction. Residues

sprayed by mistake must be cleaned off immediately using a

damp cloth.

10.1.5 Unhooking the control panel

To make assembly e.g. installation of a charging pump easier, the control

panel can be unhooked.

1. Fold the control panel (KSF) down.

2. Unhook the straps on the left and right of the KSF.

Caution

Hold the KSF to make sure it does not flop forwards.

3. The KSF can be pulled out to the right.

4. Unhook the complete KSF to the right.

Note

Make sure that the KSF can be set down safely in an appropriate

place.

10.1.6 At the end of the maintenance work

After finishing the cleaning work, re-install the heat exchanger and burn

er.

Check the nominal heat load and exhaust gas values.

Fig.35 Unhooking the control panel

RA-0000089

10 Maintenance

7658013 - 02 - 15092016

Paramount four 30 – 115 kW

129

Summary of Contents for Paramount four

















































































































































Search results

Summary of Contents for Paramount four

Reviews:

Potterton Paramount four, Installation Manual, Page: 129 / 144

Search results

Summary of Contents for Paramount four

Reviews: