manualshive.com logo in svg

Potterton Paramount four, Installation Manual, Page: 91 / 144

Share
Download
Potterton Paramount four Installation Manual Download Page 91

Time setting central heating: The DHW temperature will be switched 

over between the nominal DHW temperature value and the reduced 

nominal DHW temperature value depending on the time switching pro­

grams. Every time, the switching-on time is moved forward.

It is moved forward by 1 hour.

Time hot water: The DHW temperature is changed over between the 

DHW temperature setpoint and the reduced DHW temperature setpoint 

independently of time switching programs of the heating circuit. For this, 

time switching program 4 is used.

Charging priority (1630)

This function ensures that the boiler capacity is primarily made available 

for DHW in case of simultaneous capacity demand by room heating and 

DHW.

Absolute: Mixer and pumped heating circuits are blocked until the DHW 

has been heated up.

Shifting: Should the boiler capacity not be sufficient to heat up DHW, 

mixer and pumped heating circuits will be restricted.

None: Charging DHW is carried out in parallel with heating operation.

MC shifting, PC absolute: Pumped heating circuits are blocked until the 

DHW has been heated up. Should the boiler capacity not be sufficient, 

the mixer circuit will also be restricted.

For more information, see

Delay heat request (746, 1046, 1346), page 85

Legionella function (1640)

Function to kill legionella germs by heating up to the set legionella function 

setpoint (see programme number 1645).

Off: Legionella function is switched off.

Periodically: Legionella function is repeated periodically, depending on 

the set value (prog. no. 1641).

Fixed weekday: Legionella function will be activated on a certain week­

day (prog. no. 1642).

Legionella funct periodically (1641)

Setting the interval for the legionella function periodically (recommended 

setting in case of additional drinking water heating by solar plant in con­

nection with a storage tank mixing pump).

Legionella funct weekday (1642)

Selection of the weekday for the legionella function.

Legionella funct time (1644)

Setting the start time for the legionella function. With setting --- the legion­

ella function will be carried out the first time DHW heating is enabled.

Legionella funct setpoint (1645)

Selecting the set temperature required for killing the bacteria.

Legionella funct duration (1646)

With this function, the time is set during which the legionella function set­

point is activated to kill germs.

Fig.27 Release depending on the time 

switching programmes of the heating 

circuits (example)

RA-0000077

Fig.28 Release according to time switching 

programme 4 (example)

RA-0000078

9  Settings

7658013 - 02 - 15092016

Paramount four 30 – 115 kW

91

Summary of Contents for Paramount four

















































































































































Reviews:

No comments