Potterton Paramount four Installation Manual Download Page 123

Page: 123 / 144

End user (Eu)

Commissioning, Engineer (menu

Status)

Forced, legionella setp

Forced, nominal setp

Charg el imm heater

El charging, legionella setp

El charging, nominal setp

El charging, reduced setp

El charging, frost prot setp

El imm heater released

Boost active

Boost legionella setpoint

Boost hot water setpoint

Charging active

Charging, legionella setp

Charging, nominal setp

Charging, reduced setp

Frost protection active

Frost prot instant heater

Overrun active

Standby charging

Charged

Charged, max st tank temp

Charged, max charging temp

Charged, legionella temp

Charged, nominal temp

Charged, reduced temp

Off

Ready

Tab.29 Status table boiler

The following messages are possible under Boiler:

End user (Eu)

Commissioning, Engineer (menu

Status)

SLT has tripped

Fault

Limitter has tripped

Manual control active

Chimney sweep funct active

Chim sweep fct, full load

Chim sweep fct, part load

Locked

Locked, manual

Locked, solid fuel boiler

Locked, automatic

Locked, outside temp

Locked, economy mode

Min limitation active

Min limitation

Min limitation, part load

Min limitation active

In operation

Protective start

Protective start, part load

Return limitation

9 Settings

7658013 - 02 - 15092016

Paramount four 30 – 115 kW

123

Summary of Contents for Paramount four

















































































































































Search results

Summary of Contents for Paramount four

Reviews:

Potterton Paramount four, Installation Manual, Page: 123 / 144

Search results

Summary of Contents for Paramount four

Reviews: