manualshive.com logo in svg

Potterton Paramount four, Installation Manual, Page: 46 / 144

Share
Download
Potterton Paramount four Installation Manual Download Page 46

Caution

Risk of damage to the burner!

Too 

high

 CO

2

 values can lead to unhygienic combustion (high CO 

values) and damage to the burner.

Too 

low

 CO

2

 values can lead to ignition problems.

The CO

2

 value is set by adjusting the gas pressure at the gas valve. If the 

Paramount four is used in areas with fluctuating natural gas composition, 

the CO

2

content must be adjusted in accordance with the Wobbe index at 

any given time (ask the gas supply company).
The CO

2

 content to be set can be decided as follows:

CO

2

 content = 8.5 - (W

oN

 - W

ocurrent

) * 0,5

until Paramount four 50: CO

2

 content = 8,5 - (W

oN

 - W

ocurrent

) * 0,5

above Paramount four 50: CO

2

 content = 8.8 - (W

oN

 - W

ocurrent

) * 0.5

The air quantity set in the factory must not be changed.

For more information, see

Technical data, page 14

Technical data, page  0

7.4.4  Changing over from natural gas to LPG and vice versa

Danger

Danger! Danger to life by gas!

The gas type of the Paramount four may only be changed by an 

approved heating specialist. The Potterton Commercial conver­

sion kit for LPG (accessory) must be used. The instructions of the 

conversion kit must be observed!

The CO

2

 content is set by adjusting the injection nozzle pressure on the 

gas valve.
The CO

2

-content must be between the values according to section 

Techni­

cal Data 

at full load as well as low load.

7  Commissioning

46

Paramount four 30 – 115 kW

7658013 - 02 - 15092016

Summary of Contents for Paramount four

















































































































































Reviews:

No comments