manualshive.com logo in svg

Potterton Paramount four, Installation Manual, Page: 27 / 144

Share
Download
Potterton Paramount four Installation Manual Download Page 27

4.2  Control panel description

4.2.1  Operating elements

1 Regulator operating unit

2 Operating mode key, heating mode

3 Operating mode key domestic water mode

4 Screen

5 OK key (acknowledgement) 

6 Information key

7 Control knob

8 ESC key (cancel) 

9 Chimney sweep key

10 ON/OFF switch

11 Release key burner control

12 Pressure gauge

4.2.2  Displays

Heating to comfort setpoint

Heating to reduced setpoint

Heating to frost protection setpoint 

Current process

Holiday function active

Reference to heating circuits

Burner in operation (boiler only)

Cooling active (heat pump only)

Compressor in operation (heat pump only)

Maintenance message

Fault message

Information level active

Setting level active

Heating system switched off (automatic summer/winter changeover 

or automatic heating limit active)

4.3  Standard delivery

Gas condensing boiler for fitting to the wall, packed in a cardboard box

Info package with manual

Outside temperature sensor

Mounting rail

Accessories

4.4  Accessories and options

A list of the accessories (selection) available for the Paramount four can 

be found below.

Room device RGT

Bus module BM

Extension module EWM

Shut-off set AEH

Membrane expansion vessel MAG

Connection pipe for mixing circuit MAR

4.4.1  Installation of extension module

If an EWM extension module is installed, an application with one or two 

mixed heating circuits is possible.

Fig.9

Operating elements

1

2

3

4

5

6

7

8

9

10

11

12

XXXXXXXXXXXXX

Fig.10 Symbols on the display

sRE081B

4  Description of the product

7658013 - 02 - 15092016

Paramount four 30 – 115 kW

27

Summary of Contents for Paramount four

















































































































































Reviews:

No comments