manualshive.com logo in svg

Potterton Paramount four, Installation Manual, Page: 101 / 144

Share
Download
Potterton Paramount four Installation Manual Download Page 101

Temp diff on (4130), Temp diff off (4131) and Comparative 

temp (4133)

1 / 0 On / off boiler pump

Bx Comparative actual temperature

T1 Temp diff on

T0 Temp diff off

TKx Boiler temperature

TS Storage temperature

t Time

A sufficiently large temperature difference is necessary between the boiler 

temperature and the comparative temperature for start-up of the pump.
To maintain the comparative temperature, the following settings are avail­

able under prog. no. 4133:

Hot water sensor B3 / Hot water sensor B31: The comparative tempera­

ture is supplied by the DHW sensor B3/B31.

Buffer sensor B4 / Buffer sensor B41: The comparative temperature is 

supplied by the buffer storage tank sensor B4/B41.

Flow temp setpoint: The flow temperature setpoint is used as compara­

tive temperature.

Setpoint min: The value set in prog.no. 4110 is used as comparative 

temperature.

Pump overrun time (4140)

Setting pump after-run time.

9.2.15 Buffer storage tank

Auto generation lock (4720)

The hydraulic separation of heat generator and buffer storage tank is ach­

ieved by the automatic heat generator lock. The heat generator is only put 

into operation if the buffer can no longer cover the current heat demand. 

The following settings are possible:

None: The automatic heat generator lock is deactivated.

With B4: The automatic heat generator lock is triggered by the buffer 

cylinder B4.

With B4 and B42/B41: The automatic heat generator lock is triggered by 

the buffer cylinders B4 and B41/B42.

Auto heat gen lock SD (4721)

The heat generator is locked if the the temperature in the buffer storage 

tank is higher than the boiler sAuto heat gen lock SD.

Temp diff buffer/CH (4722)

If the temperature difference between buffer storage tank and heating cir­

cuit temperature request is large enough, the heat required by the heating 

circuit will be taken from the buffer storage tank. The heat generator is 

locked.

Min st tank temp heat mode (4724)

If the storage tank temperature of the buffer storage tank drops below this 

value, the heating circuit is switched of if no generator is available.

Charging temp max (4750)

The buffer storage tank is charged from solar energy up to the set charg­

ing temperature maximum.

Note

The collector overheating protection function can put the collector 

pump back in operation until the maximum storage tank tempera­

ture is reached.

Recooling temp (4755)

The collector overheating protection function can put the collector pump 

back in operation until the maximum storage tank temperature is reached.

Fig.31 Storage tank charging

1

0

TKx

T1

T0

TS

Bx

T

t

RA-0000081

9  Settings

7658013 - 02 - 15092016

Paramount four 30 – 115 kW

101

Summary of Contents for Paramount four

















































































































































Reviews:

No comments