manualshive.com logo in svg

Potterton Paramount four, Installation Manual, Page: 35 / 144

Share
Download
Potterton Paramount four Installation Manual Download Page 35

6  Installation

6.1  Water connections

6.1.1  Connecting the heating circuit

Connect the heating circuit with flat seal screw connections to boiler flow 

and boiler return.
Disconnector valves have to be installed into the flow and return. To facili­

tate the assembly, the shut-off set ADH (accessory) or AEH (accessory) 

may be used.
Disconnector valves have to be installed into the flow and return. To facili­

tate the assembly, the shut-off set ADH (accessory) may be used.

Note

Install heating filter.

Installation of a filter is recommended in the heating return. In the 

case of old plants, the whole heating plant should be thoroughly 

flushed before installation.

6.1.2  Safety valve

Mount the membrane expansion vessel with the heating systems closed.

Caution

The connecting pipe between boiler and safety valve must not be 

blockable.

The installation of pumps and fittings or pipe reducer pieces is not 

permissible. The blow-off line of the safety valve must be de­

signed in such a way that the pressure does not increase when 

the safety valve responds. It must not be routed to the outside, the 

opening must be clear and observable. Any heating water that 

may possibly escape should be safely drained off.

Caution

The blow-off line of the safety valve must be designed in such a 

way that the pressure does not increase when the safety valve re­

sponds. It must not be routed to the outside, the opening must be 

clear and observable. Any heating water that may possibly escape 

should be safely drained off.

6.1.3  Condensate

A direct run-off of the condensate into the domestic drainage system is on­

ly allowed if the system only comprises corrosion-resistant materials (e.g. 

PP-pipe, stoneware or similar materials).
The condensate must be able to flow freely into a funnel. A stench trap 

must be installed between the funnel and drainage system.
The condensate hose of the Paramount four must be inserted through the 

opening in the floor.
If there is no run-off facility underneath the condensate discharge, the use 

of Potterton Commercial neutralisation and lifting system is recommended.

Fig.14 Installation of disconnector valves

RA-0000056

6  Installation

7658013 - 02 - 15092016

Paramount four 30 – 115 kW

35

Summary of Contents for Paramount four

















































































































































Reviews:

No comments