Potterton Paramount four Installation Manual Download Page 124

Page: 124 / 144

End user (Eu)

Commissioning, Engineer (menu

Status)

Return limitation, part load

Charging buffer

In part load op for CH, HW

Released for CH and HW

In operation for HW

In part load op for HW

Released for HW

In operation for CH

In part load op for CH

Released for CH

Overrun active

Released

Frost protection active

Off

Tab.30 Status table solar

The following messages are possible under Solar:

End user (Eu)

Commissioning, Engineer (menu

Status)

Manual control active

Fault

Frost prot collector active

Recooling active

Max st tank temp reached

Evaporation prot active

Overtemp protect active

Max charging temp reached

Charg HW+swi pool

Charging HW+buffer

Charging HW+swi pool

Charging swi pool

Charging HW

Charging buffer

Charging swimming pool

Radiation insufficient

Min charg temp not reached

Temp diff insufficient

Radiation insufficient

Tab.31 Status table solid fuel boiler

The following messages are possible under Solid fuel boiler:

End user (Eu)

Commissioning, Engineer (menu

Status)

Manual control active

Fault

9 Settings

124

Paramount four 30 – 115 kW

7658013 - 02 - 15092016

Summary of Contents for Paramount four

















































































































































Search results

Summary of Contents for Paramount four

Reviews:

Potterton Paramount four, Installation Manual, Page: 124 / 144

Search results

Summary of Contents for Paramount four

Reviews: