manualshive.com logo in svg

Pontiac 2000 Montana, Owner'S Manual

Share
Download
Pontiac 2000 Montana Owner'S Manual Download Page 96

1-84

Securing a Child Restraint in the 
Right Front Seat Position

Your vehicle has a front passenger air bag. Never put a
rear

-

facing child restraint in this seat. Here’s why:

CAUTION:

A child in a rear

-

facing child restraint can be

seriously injured or killed if the front passenger’s
air bag inflates. This is because the back of the
rear

-

facing child restraint would be very close 

to the inflating air bag. If your vehicle is a
passenger van, always secure a rear

-

facing 

child restraint in a rear seat.

Although a rear seat is a safer place, you can secure a
forward

-

facing child restraint in the right front seat.

You’ll be using the lap

-

shoulder belt. See the earlier 

part about the top strap if the child restraint has one. 
Be sure to follow the instructions that came with the
child restraint. Secure the child in the child restraint
when and as the instructions say.

1. Because your vehicle has a front passenger air 

bag, always move the seat as far back as it will go
before securing a forward

-

facing child restraint. 

(See “Seats” in the Index.)

2. Put the restraint on the seat.

3. Pick up the latch plate, and run the lap and shoulder

portions of the vehicle’s safety belt through or
around the restraint. The child restraint instructions
will show you how.

Summary of Contents for 2000 Montana













































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands