manualshive.com logo in svg

Pontiac 2000 Montana, Owner'S Manual

Share
Download
Pontiac 2000 Montana Owner'S Manual Download Page 167

2-64

Fog Lamps

The fog lamps switch is
located in the instrument
panel switchbank. Push the
fog lamp symbol on the
switch to turn on the lamps.

The indicator light will glow when the fog lamps are on.
Push the ribbed part of the switch to turn them off. 
The indicator light will go off.

Your parking lamps or headlamps must be on for your
fog lamps to go on.

When your DRL are on, the headlamp switch must first be  
turned from the off position before the fog lamps can be
turned on. At night, when the light sensor automatically
turns on your headlamps, the fog lamps can be turned 
on when the headlamps switch is in any position.

Your fog lamps will go off when you switch to high beams.
Using your high beams in fog is not recommended.

Interior Lamps

Instrument Panel Intensity Control

Turn the control, located below the headlamps switch,
clockwise to increase the brightness of the instrument
panel lights, and counterclockwise to decrease the
brightness. Turn the control all the way
counterclockwise to turn them off.

Interior Lamps Control

Turn the dial all the way clockwise to turn on the
interior lamps, if the interior lamps override switch is
off. Turn the dial counterclockwise to turn the lamps off.

Summary of Contents for 2000 Montana













































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands