manualshive.com logo in svg

Pontiac 2000 Montana, Owner'S Manual

Share
Download
Pontiac 2000 Montana Owner'S Manual Download Page 281

4-32

Towing a Trailer

CAUTION:

If you don’t use the correct equipment and drive
properly, you can lose control when you pull a
trailer. For example, if the trailer is too heavy, 
the brakes may not work well 

--

 or even at all.

You and your passengers could be seriously
injured. Pull a trailer only if you have followed
all the steps in this section. Ask your dealer for
advice and information about towing a trailer
with your vehicle.

NOTICE:

Pulling a trailer improperly can damage your
vehicle and result in costly repairs not covered by
your warranty. To pull a trailer correctly, follow
the advice in this part, and see your dealer for
important information about towing a trailer
with your vehicle.

Your vehicle can tow a trailer. To identify what 
the vehicle trailering capacity is for your vehicle, 
you should read the information in “Weight of 
the Trailer” that appears later in this section. But 
trailering is different than just driving your vehicle by
itself. Trailering means changes in handling, durability
and fuel economy. Successful, safe trailering takes
correct equipment, and it has to be used properly.

That’s the reason for this section. In it are many
time

-

tested, important trailering tips and safety rules.

Many of these are important for your safety and that 
of your passengers. So please read this section carefully
before you pull a trailer.

Load

-

pulling components such as the engine, transaxle,

wheel assemblies and tires are forced to work harder
against the drag of the added weight. The engine is
required to operate at relatively higher speeds and under
greater loads, generating extra heat. What’s more, the
trailer adds considerably to wind resistance, increasing
the pulling requirements.

Summary of Contents for 2000 Montana













































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands