manualshive.com logo in svg

Pontiac 2000 Montana, Owner'S Manual

Share
Download
Pontiac 2000 Montana Owner'S Manual Download Page 143

2-40

RUN (D): This is an on position to which the switch
returns after you start your engine and release the
switch. The switch stays in RUN when the engine is
running. But even when the engine is not running, 
you can use RUN to operate your electrical power
accessories, and to display some instrument panel
warning lights.

START (E): This position starts the engine. When the
engine starts, release the key. The ignition switch will
return to RUN for normal driving.

If the engine is not running, ACCESSORY and RUN 
are positions that allow you to operate your electrical
accessories, such as the radio.

Retained Accessory Power (RAP)

With RAP, the power windows (option), the power 
rear quarter windows (if equipped), audio system and
electronic level control (ELC) will continue to work up
to 10 minutes after the ignition key is turned to OFF 
and none of the doors are opened.

Starting Your Engine

Move your shift lever to PARK (P) or NEUTRAL (N).
Your engine won’t start in any other position 

--

 that’s a

safety feature. To restart when you’re already moving,
use NEUTRAL (N) only.

NOTICE:

Don’t try to shift to PARK (P) if your vehicle is
moving. If you do, you could damage the
transaxle. Shift to PARK (P) only when your
vehicle is stopped.

1. Without pushing the accelerator pedal, turn your

ignition key to START. When the engine starts, let
go of the key. The idle speed will go down as your
engine gets warm.

Summary of Contents for 2000 Montana













































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands