manualshive.com logo in svg

Pontiac 2000 Montana, Owner'S Manual

Share
Download
Pontiac 2000 Montana Owner'S Manual Download Page 285

4-36

Safety Chains

You should always attach chains between your vehicle
and your trailer. Cross the safety chains under the 
tongue of the trailer to help prevent the tongue from
contacting the road if it becomes separated from the
hitch. Instructions about safety chains may be provided
by the hitch manufacturer or by the trailer manufacturer.
Follow the manufacturer’s recommendation for attaching
safety chains and do not attach them to the bumper.
Always leave just enough slack so you can turn with 
your rig. Never allow safety chains to drag on the ground.

Trailer Brakes

If your trailer weighs more than 1,000 lbs. (450 kg)
loaded, then it needs its own brakes 

--

 and they must 

be adequate. Be sure to read and follow the instructions
for the trailer brakes so you’ll be able to install, adjust
and maintain them properly.

Because you have anti

-

lock brakes, do not try to tap 

into your vehicle’s brake system. If you do, both brake
systems won’t work well, or at all.

Driving with a Trailer

CAUTION:

If you have a rear

-

most window open and you

pull a trailer with your vehicle, carbon monoxide
(CO) could come into your vehicle. You can’t see
or smell CO. It can cause unconsciousness or
death. (See “Engine Exhaust” in the Index.) 
To maximize your safety when towing a trailer:
D Have your exhaust system inspected for

leaks, and make necessary repairs before
starting on your trip.

D Keep the rear

-

most windows closed.

D If exhaust does come into your vehicle

through a window in the rear or another
opening, drive with your front, main
heating or cooling system on and with the
fan on any speed. This will bring fresh,
outside air into your vehicle. Do not use
RECIRCULATION because it only
recirculates the air inside your vehicle. 
(See “Comfort Controls” in the Index.)

Summary of Contents for 2000 Montana













































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands