manualshive.com logo in svg

Pontiac 2000 Montana, Owner'S Manual

Share
Download
Pontiac 2000 Montana Owner'S Manual Download Page 27

1-15

To raise a seatback, pull the nylon strap while raising the
seatback until it locks upright.

To fold down the 
seatback, lift up on this
lever located on the 
front of the seatback.

Use the lever to raise or lower the seatback to the
desired position.

When raising or reclining a seatback to an upright
position, push and pull on the seatback to check that 
it is locked upright.

Adjusting the Bucket Seats

There are two adjustment levers on each seat to adjust
the seat forward or rearward.

One is located below the center, in front of the bucket seat.

Summary of Contents for 2000 Montana













































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands