manualshive.com logo in svg

Pontiac 2000 Montana, Owner'S Manual

Share
Download
Pontiac 2000 Montana Owner'S Manual Download Page 156

2-53

Windows

Manual Windows

Use the manual crank to open and close the front windows.

Power Windows (Option)

If you have power windows, the switches on the 
driver’s door armrest control the front windows (when
the ignition is in RUN, ACCESSORY or when retained
accessory power (RAP) is active). (See “Retained
Accessory Power” in the Index.) The left switch controls
the driver’s window. The right switch controls the
passenger’s window.

The driver’s power window switch has two down
positions. Push the switch to the first position to 
lower the window normally.

To activate the auto

-

down feature, push the switch all

the way down, then release. The window will lower
completely. To stop the window from lowering all the
way, pull up the front of the switch.

To raise the window, pull up the front of the switch.

Summary of Contents for 2000 Montana













































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands