manualshive.com logo in svg

Pontiac 2000 Montana, Owner'S Manual

Share
Download
Pontiac 2000 Montana Owner'S Manual Download Page 126

2-23

Vehicles are delivered programmed in Mode 1.

To change the mode:

1. Follow the instructions for “Entering Programming

Mode” listed previously.

2. Insert your second key fully into any door key

cylinder and turn it to the unlock position.

This step is necessary to prevent accidental
programming of this feature to Mode 2. Do not
program this feature to Mode 2 without first reading
Mode 2 entirely. The door key cylinder must remain
in the unlock position during Steps 2 through 4.

3. Press the horn symbol on the remote keyless 

entry transmitter.

4. Count the number of chimes you hear. The 

number of chimes tells you which mode your 
vehicle is in. You can change the mode by 
pressing the horn symbol on the remote keyless 
entry transmitter again.

5. Repeat Step 3 until you hear the number of 

chimes that matches the mode you want.

6. Remove your key from the door key cylinder.

The mode you selected is now set. You can either exit
the programming mode by following the instructions
next in this section or program the next feature available
on your vehicle.

Exiting Programming Mode

To exit programming mode, just turn the key from
ACCESSORY to OFF and put the BCM PRGRM 
fuse back into the instrument panel fuse block.

After programming a feature, you can exit the
programming mode at anytime. Also, if your vehicle 
is equipped with the content theft

-

deterrent system,

remember to arm the system before exiting.

Sliding Door

To open the sliding door from outside the vehicle, pull
the handle out and then pull the door toward the rear. 
If you slide the door all the way back, the door will rest
in a detent position. The door must overcome this detent
when closing.

To move the door forward, you must first pull the door
past the open detent position.

If your vehicle has a sliding door on the driver’s side,
the door is designed to open only a little if the fuel 
door is open. If this ever happens, don’t try to force 
the sliding door. Just close the driver’s side sliding door.
Then when the fuel filler door is closed, the driver’s side
sliding door can be opened normally.

Summary of Contents for 2000 Montana













































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands