manualshive.com logo in svg

Pontiac 2000 Montana, Owner'S Manual

Share
Download
Pontiac 2000 Montana Owner'S Manual Download Page 356

6-35

7. To reinstall the lamp assembly, line up and insert the

tabs on the back of the assembly with the slots in the
fender. Engage the lower clip on the front of the
lamp assembly, keeping the upper tab on the
parking/turn signal lamp assembly inboard of the
headlamp bracket tab.

8. To align the parking/turn signal lamp assembly with the 

headlamp assembly, lift up the parking/turn signal lamp 
assembly until the upper edge is contacting the fender.

9. Fasten the parking/turn signal lamp assembly to the

headlamp assembly with the thumb screw removed
in Step 2.

Front Sidemarker

1. Open the hood.

2. Remove the thumb screw attaching the parking/turn

signal lamp assembly to the headlamp assembly.

3. Pull the parking/turn signal lamp assembly away

from the vehicle.

4. Unscrew the bulb socket from the lamp assembly by

turning it counterclockwise.

Summary of Contents for 2000 Montana













































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands