manualshive.com logo in svg

Pontiac 2000 Montana, Owner'S Manual

Share
Download
Pontiac 2000 Montana Owner'S Manual Download Page 32

1-20

Captain’s Chairs

The captain’s chairs adjust like the manual front
passenger seats.

The seatback can be
reclined or raised by 
turning the knob located 
on the inboard side of 
the seat.

It is easier to raise or lower the seatback if you lean
forward and take the weight off the seatback.

The armrests can be lowered or raised for entering or
exiting the vehicle.

The seatbacks on the second
row captain chairs fold
forward to put items behind
the left anf right seats.

Lift the lever and fold 
the seatback forward.

The seatback will lock into place when you push it back 
to the upright position.

The seatback lever will not lift and fold if the seatback 
is at an 88

_ angle or less.

CAUTION:

If the seatback isn’t locked, it could move forward
in a sudden stop or crash. That could cause injury
to the person sitting there. Always press rearward
on the seatback to be sure it is locked.

Summary of Contents for 2000 Montana













































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands