Pontiac 2000 Montana Owner'S Manual Download Page 310

Page: 310 / 428

5-22

Removing the Spare Tire and Tools

The equipment you’ll need
is located in the storage
compartment at the rear
of the vehicle, on the
passenger’s side.

1. Remove the side convenience net.

2. Open the jack storage compartment by lifting up the

tab and pulling the cover off.

A. Jack

B. Strap

C. Bracket

D. Wing Nut

E. Jacking Instructions

F. Bag and Tools

Remove the jack and jacking tools by loosening the
wing nut and bracket.

Separate the plastic pouch from the jack and remove
the jacking tools (folding wrench and extension) from
the pouch.

Summary of Contents for 2000 Montana












































































































































































































































































































































































































































Search results

Summary of Contents for 2000 Montana

Reviews:

Brands by name

Popular brands

Pontiac 2000 Montana, Owner'S Manual

Search results

Summary of Contents for 2000 Montana

Reviews:

Brands by name

Popular brands