manualshive.com logo in svg

Pontiac 2000 Montana, Owner'S Manual

Share
Download
Pontiac 2000 Montana Owner'S Manual Download Page 345

6-24

Add coolant mixture at the recovery tank, but be careful
not to spill it.

CAUTION:

You can be burned if you spill coolant on hot
engine parts. Coolant contains ethylene glycol,
and it will burn if the engine parts are hot
enough. Don’t spill coolant on a hot engine.

Occasionally check the coolant level in the radiator. 
For information on how to add coolant to the radiator,
see “Cooling System” in the Index.

Radiator Pressure Cap

NOTICE:

Your radiator cap is a 15 psi (105 kPa)
pressure

-

type cap and must be tightly installed to

prevent coolant loss and possible engine damage
from overheating. Be sure the arrows on the cap
line up with the overflow tube on the radiator
filler neck.

Power Steering Fluid

The power steering fluid
reservoir is located to the
right of the windshield
washer fluid reservoir, 
at the back of the 
engine compartment.

Summary of Contents for 2000 Montana













































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands