manualshive.com logo in svg

Pontiac 2000 Montana, Owner'S Manual

Share
Download
Pontiac 2000 Montana Owner'S Manual Download Page 245

3-37

P.SET PROG: The front passengers must be listening
to something different for each of these functions 
to work:
D Press this button to seek through your preset radio

stations set on your primary radio pushbuttons. 
The display will show your selections.

D When a cassette tape is playing, press this button to

go to the other side of the tape.

TAPE CD: With a cassette tape in the player and the
radio playing, press this button to play a cassette tape.
Press TAPE CD to switch between the tape and compact
disc if both are loaded. Press AM

-

FM to return to the

radio when a cassette tape or compact disc is playing.
The inactive tape or CD will remain safely inside the
radio for future listening.

Theft

-

Deterrent Feature RDS Radios

THEFTLOCK

R

 is designed to discourage theft of 

your radio. The feature works automatically by learning
a portion of the Vehicle Identification Number (VIN). 
If the radio is moved to a different vehicle, it will not
operate and LOCKED will be displayed.

With THEFTLOCK activated, your radio will not
operate if stolen.

Theft-Deterrent Feature (If Equipped)
Non-RDS Radios (Canada Only)

THEFTLOCK

R

 is designed to discourage theft of 

your radio. The feature works automatically by learning
a portion of the Vehicle Identification Number (VIN). 
If the radio is moved to a different vehicle, it will not
operate and LOC will be displayed.

With THEFTLOCK activated, your radio will not
operate if stolen.

Summary of Contents for 2000 Montana













































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands