manualshive.com logo in svg

Pontiac 2000 Montana, Owner'S Manual

Share
Download
Pontiac 2000 Montana Owner'S Manual Download Page 171

2-68

Cargo Lamp

The cargo lamp is located in the rear of your vehicle,
above the liftgate opening, and has no switch of its own.
It will go on each time you open the doors, unless you
turn on the interior lamps override.

Battery Saver

Your vehicle has a feature to help prevent you from
draining the battery, in case you accidentally leave the
interior lamps on. If you leave any interior lamps on
while the ignition is in LOCK or OFF, they will
automatically turn off after 10 minutes. The lamps 
won’t come back on again until you:
D Turn the ignition to RUN or ACCESSORY,
D turn the interior lamps dial all the way clockwise,

then slightly back counterclockwise, or

D open (or close and reopen) a door that is closed.
If your vehicle has less than 15 miles (25 km) on the
odometer, the battery saver will turn off the lamps after
only three minutes.

Mirrors

Inside Day/Night Rearview Mirror

To reduce glare from lights behind you, pull the lever
toward you (to the night position). To return the mirror
to the day position, push the lever away from you.

Power Remote Control Mirrors

The control located on the
driver’s door operates both
outside rearview mirrors.

Summary of Contents for 2000 Montana













































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands