manualshive.com logo in svg

Pontiac 2000 Montana, Owner'S Manual

Share
Download
Pontiac 2000 Montana Owner'S Manual Download Page 208

2-105

Turn the ignition on and cycle the DIC to the
compass/temperature mode. Press both the E/M and
MODE buttons simultaneously for at least 10 seconds
until the calibration symbol appears. Release both
buttons and complete three 360

_ turns in an area free

from large metal objects. The calibration symbol will
turn off and the compass reading will be displayed.

Error Displays

D An error of the vehicle’s speed sensor or fuel sender

will cause 

-

E

-

 to be displayed.

D In the absence of vehicle communications, a double

dash “

--

” is displayed.

If one of these error messages appear, see your dealer.

Trip Computer

There are five trip computer displays which may be
stepped through by pushing the MODE button. 
The information will appear in the following order:
D AVG ECON (Average Fuel Economy): This shows

the average fuel economy since the last reset.

D INST ECON (Instantaneous Fuel Economy): 

This shows fuel economy for the most recent second
of driving.

D RANGE (Trip Range): This shows the estimated

distance that can be traveled with the remaining fuel.
The fuel economy used to calculate range is based on
the last few hours of driving.

D FUEL USED (Trip Fuel Used): This shows the

accumulated fuel used since the last reset.

D AVG SPEED (Average Speed): This shows the

average speed since the last reset.

Resetting the Trip Computer

Press and hold the MODE and E/M buttons for at least
two seconds. The reset is acknowledged with the display
showing all segments on briefly. A reset can only be
done in AVG ECON, FUEL USED and AVG SPEED
displays. AVG ECON, FUEL USED and AVG SPEED
can be reset independently. Only the mode that is
displayed will be reset.

Summary of Contents for 2000 Montana













































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands