Polycom MGC Manager User Manual Download Page 360

Page: 360 / 382

Chapter 8 - Recording

8-12

In the

DTMF Codes

dialog box, scroll down the list of messages to the

the three recording messages:

—

Start Recording

—

Stop Recording

—

Pause Recording

Optional. To change the default settings for a recording DTMF, select the
message from the

Name

column and modify its

DTMF Code

Permission

in the boxes

below the table.

Click

Finish

The IVR Service you defined is listed in the

MCU Configuration

under

the

IVR Msg Services

icon. You can now apply the service to the

conferences you want to record.

Default service

•

You can modify the parameters of a service, but not its name. To modify a a
message service, right-click its icon or name and click

Properties

•

If you defined several services, you can select one of them as the default.
Right-click the service icon and click

Set As Default

. The name of default

service is bolded.

Summary of Contents for MGC Manager































































































































































































































































































































































































Search results

Summary of Contents for MGC Manager

Reviews:

Related manuals for MGC Manager

Brands by name

Popular brands

Polycom MGC Manager, User Manual

Search results

Summary of Contents for MGC Manager

Reviews:

Related manuals for MGC Manager

Brands by name

Popular brands