Polycom MGC Manager User Manual Download Page 135

Page: 135 / 382

MGC Manager User’s Guide - VoicePlus Edition

3-37

The following information is displayed for the disconnected participant:

Table 3-12: ISDN Participant Properties - Disconnection Cause

Field/Option

Description

Call
Disconnection
Reason

Lists the reasons for participant's disconnection:

•

Operator Disconnect

– The participant was

disconnected from the conference by the operator.

•

No Net Connection

– Network channels could not

be connected. This reason may occur when the
telephone lines are unavailable or busy.

•

Participant Hang Up

– The participant

disconnected himself from the conference.

•

Bad H.243 Connection

– Problems occurred with

the connection protocol.

•

Resource Deficiency

– Hardware resources (audio

or network cards) are insufficient and cannot handle
the conference.

•

Security Failure

– Encryption related problem

prevented the connection. Not relevant to ISDN
Audio Only participant.

Cause

Describes the cause of disconnection according to the
category indicated in the

Call Disconnection Reason

For example, when

Operator Disconnect

is selected,

the name of the

Cause

field is changes to

Operator

Name

and lists the name of the operator who

disconnected the participant.

Summary of Contents for MGC Manager































































































































































































































































































































































































Search results

Summary of Contents for MGC Manager

Reviews:

Related manuals for MGC Manager

Brands by name

Popular brands

Polycom MGC Manager, User Manual

Search results

Summary of Contents for MGC Manager

Reviews:

Related manuals for MGC Manager

Brands by name

Popular brands