Polycom MGC Manager User Manual Download Page 128

Page: 128 / 382

Chapter 3 - Monitoring On Going Conferences

3-30

The

Participant Properties - Connection Info1

dialog box opens.

The following information is displayed for the connected participant:

Table 3-9: ISDN Participant Properties - Connection Info1

Field/Option

Description

Participant State

The current connection status of the participant.

Note:

This status is indicated in the

Monitor

and

Status

panes. For more details, see Table 3-2 on

page 3-7.

Disconnect/
Reconnect

Depending on the current participant status in the
On Going Conference, this button lets you
disconnect or reconnect

the participant.

Channels Status

The status of the participant's audio channel
according to the following parameters:

•

Channel

– Indicates the connection status of the

audio channel. A check mark next to the audio
channel indicates that it is connected.

Summary of Contents for MGC Manager































































































































































































































































































































































































Search results

Summary of Contents for MGC Manager

Reviews:

Related manuals for MGC Manager

Brands by name

Popular brands

Polycom MGC Manager, User Manual

Search results

Summary of Contents for MGC Manager

Reviews:

Related manuals for MGC Manager

Brands by name

Popular brands