Polycom MGC Manager User Manual Download Page 122

Page: 122 / 382

Chapter 3 - Monitoring On Going Conferences

3-24

In an On Going Conference, two new tabs appear in the

Conference

Properties

dialog box that were not applicable during the conference

definition:

—

Scheduler

—

On Going State

You can view the conference general parameters and, if remarks have
been entered, review the remarks history.

Click the

Scheduler

tab to view the date and time at which the

conference had started and to view the ending time that was scheduled
for the conference.
The

Conference Properties - Scheduler

dialog box opens.

To shorten or extend the conference, you can adjust the conference
ending date and time.

Summary of Contents for MGC Manager































































































































































































































































































































































































Search results

Summary of Contents for MGC Manager

Reviews:

Related manuals for MGC Manager

Brands by name

Popular brands

Polycom MGC Manager, User Manual

Search results

Summary of Contents for MGC Manager

Reviews:

Related manuals for MGC Manager

Brands by name

Popular brands