Polycom MGC Manager User Manual Download Page 110 | Manualshive

Page: 110 / 382

background image

Chapter 3 - Monitoring On Going Conferences

3-12

Connection
(cont.)

Partial
connection

The connection process is not yet
complete.

Faulty
Connection

The participant is connected, but
problems occurred in the
connection, such as
synchronization loss.

Noisy Line

The line of this participant was
detected by the system as noisy.

Note:

This indicator is used only

when the automatic noisy line
detection option was enabled in
the “system.cfg”.

Network
ISDN/T1-
CAS, H.323
or SIP

The type of supported network that the conference is using.

Participant
Numbers\
IP Address\
SIP Address

Displays the participant and MCU phone numbers or IP address/
alias, depending on the supported network and connection type.
In dial-in connection, displays the CLI number (ISDN) or IP
address/alias of the participant calling the MCU (marked by the
letter P) and the MCU number or IP address/alias dialed by the
participant (marked by the letter M). In dial-out connection
displays the dialed number (ISDN), IP address/alias (H.323) or
URI(SIP) of the participant.

Connection
Type

Identifies the defined type of participant's connection to the
conference.

Dial-out

The MCU (conference) dials to the
participant.

Dial-in

The participant calls the MCU
(conference).

Direct
connection

Leased Line connection (ISDN
only).

Table 3-2: On Going Conference - Monitor Pane Columns (Continued)

Column
Name

Icon

Indication

Description

«
...
108
109
110
111
112
...
»

Summary of Contents for MGC Manager































































































































































































































































































































































































Reviews:

No comments

Related manuals for MGC Manager

Brand: Xerox Pages: 28

DRAGON NATURALLYSPEAKING 7

Brand: ScanSoft Pages: 222

SmartWare R2.00

Brand: Inalp Networks Pages: 321

GROUPWISE 7 - WEB ACCESS

Brand: Novell Pages: 110

Brand: McAfee Pages: 205

Brand: Red Hat Pages: 198

SMROUTERUPDATINGFIRMWARE

Brand: Belkin Pages: 4

Brand: Lucent Technologies Pages: 198

Brand: Sony Pages: 1

Walkman D-NE319

Brand: Sony Pages: 2

Brand: Sony Pages: 2

VAIO VGN-TXN17P/T

Brand: Sony Pages: 2

VAIO VGN-TXN19P

Brand: Sony Pages: 2

VAIO VGN-TXN17P/B

Brand: Sony Pages: 2

VAIO VGN-TXN15P/W

Brand: Sony Pages: 2

VAIO VGN-TXN15P/T

Brand: Sony Pages: 2

VAIO VGN-TXN15P/B

Brand: Sony Pages: 2

VAIO VGN-TXN15P - VAIO - Core Solo 1.2 GHz

Brand: Sony Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands