Pioneer AVIC-S1 User Manual Download Page 110

Page: 110 / 124

User's manual AVIC-S1

- 108 -

Hardware

Information

Meaning

GMT

Greenwich Mean Time
London time without summertime.

Lon/Lat

Current position.
Specifies the East longitudinal and north

latitudinal degrees.

Satellites

Number of receiving satellites. For a

navigation, the signals require at least three
satellites.

HDOP

Horizontal Dilution of Precision
Indicates the quality of the positioning.
Theoretically, values from 0 to 50 are

possible, whereby it follows: the smaller the
value, the more precise the positioning

(value 0= no deviation from the actual
position). Values up to 8 are acceptable for

navigation purposes.

Speed

Shows the current speed of the vehicle.

Location Shows

the

current location.

Tap on the Back button to close the GPS

TATUS

window.

8.13.6

Radio-mute

Radio-mute

Radio mute only works when the mute line of the TMC kit
ND-TMC1 is connected to a car radio.
If radio mute iss et to "On", the audio of the car radio will be

muted while there is voice guidance, incoming call, etc.
The current setting is shown on the button. Tap on the button to

change the setting.

Setting

Meaning

Radio mute switched on

Off

Radio mute switched off

Summary of Contents for AVIC-S1





























































































































Search results

Summary of Contents for AVIC-S1

Reviews:

Related manuals for AVIC-S1

Brands by name

Popular brands

Pioneer AVIC-S1, User Manual

Search results

Summary of Contents for AVIC-S1

Reviews:

Related manuals for AVIC-S1

Brands by name

Popular brands