Pioneer AVIC-S1 User Manual Download Page 113

Page: 113 / 124

User's manual AVIC-S1

Configuring AVIC-S1

- 111 -

8.14.4

Distance

Distance

With this setting you establish which units of measurement
should be used for the distances.
The current setting is shown on the button. Tap on the button to
change the setting.

Setting

Meaning

Kilometres

Displays the distances in kilometres.

Miles

Displays the distances in miles.

8.15

Product Information

Product Information

The name and version of the software is displayed in the
P

RODUCT

NFORMATION

settings window.

Tap on the button to open the P

RODUCT

NFORMATION

window.

Guided Tour

Tap on the Guided Tour button to have the most important

functions of the software explained.

8.16

Restore Factory Settings

Restore Factory

Settings

Use this setting to restore to factory settings.
Tap on the button to restore the factory settings.

Summary of Contents for AVIC-S1





























































































































Search results

Summary of Contents for AVIC-S1

Reviews:

Related manuals for AVIC-S1

Brands by name

Popular brands

Pioneer AVIC-S1, User Manual

Search results

Summary of Contents for AVIC-S1

Reviews:

Related manuals for AVIC-S1

Brands by name

Popular brands