Pioneer AVIC-S1 User Manual Download Page 41

Page: 41 / 124

User's manual AVIC-S1

Navigation

- 39 -

The S

UBCATEGORY

window opens. The category that you have

chosen is specified at the top.

Use the Up and Down buttons (or the scrolling wheel) to
scroll through the list of subcategories.

Tap on the subcategory in which you'd like to find a point of
interest.

If you do not want to specify a subcategory, tap on All
categories (topmost entry).
The P

OINTS OF INTEREST IN A CITY

window opens. The

subcategory that you have just chosen is specified at the top.

The keyboard appears below.

All the destinations of the specified category / subcategory in

which the specified city has been found are listed above the
keyboard.

10.

Use the Up and Down buttons (or the scrolling wheel) in

order to scroll through the list of points of interest.

11.

Tap on the point of interest to which you would like to drive.

The route is calculated. When the calculation is concluded, the
map is shown.

Summary of Contents for AVIC-S1





























































































































Search results

Summary of Contents for AVIC-S1

Reviews:

Related manuals for AVIC-S1

Brands by name

Popular brands

Pioneer AVIC-S1, User Manual

Search results

Summary of Contents for AVIC-S1

Reviews:

Related manuals for AVIC-S1

Brands by name

Popular brands