Pioneer AVIC-S1 User Manual Download Page 59

Page: 59 / 124

User's manual AVIC-S1

Navigation

- 57 -

Save route

Open the I

TINERARY

window. (refer to page 53).

Tap on the Save button in order to save a new route.
The E

NTER

TINERARY

AME

window opens.

Enter a name for the route.

Tap on OK.

Note: Only the waypoints will be saved. When you download
a saved route, it will have to be recalculated.

Load route

Open the I

TINERARY

window. (refer to page 53).

Tap on the Load button in order to download a saved route

that you wish to either edit or navigate to.
The L

OAD ITINERARY

screen opens:

Use the Up and Down buttons (or the scrolling wheel) to
scroll through the list.

Tap on the route that you wish to download.
The I

TINERARY

window opens again. The saved waypoints are

entered in the list of waypoints.

Summary of Contents for AVIC-S1





























































































































Search results

Summary of Contents for AVIC-S1

Reviews:

Related manuals for AVIC-S1

Brands by name

Popular brands

Pioneer AVIC-S1, User Manual

Search results

Summary of Contents for AVIC-S1

Reviews:

Related manuals for AVIC-S1

Brands by name

Popular brands