Pioneer AVIC-S1 User Manual Download Page 108

Page: 108 / 124

User's manual AVIC-S1

- 106 -

Hardware

8.13.2

Click sound

Click sound

With this setting you can establish whether there should be a
click sound when tapping on the touch screen or not.
The current setting is shown on the button. Tap on the button to
change the setting.

Setting

Meaning

Click sound is switched on.

Off

Click sound is switched off.

8.13.3

Brightness

Brightness

In the B

RIGHTNESS

settings window you can establish the

brightness for the daylight and night time display.
1.

Tap on the Brightness button.
The B

RIGHTNESS

window opens.

Brightness day

The current degree of brightness is displayed between the two

buttons "-" and "+".

Tap on the "+" button to increase the value.

Tap on the "-" button to reduce the value.

Brightness night

The current degree of brightness is displayed between the two

buttons "-" and "+".

Tap on the "+" button to increase the value.

Tap on the "-" button to reduce the value.

Tap on Back in order to close the B

RIGHTNESS

window.

Summary of Contents for AVIC-S1





























































































































Search results

Summary of Contents for AVIC-S1

Reviews:

Related manuals for AVIC-S1

Brands by name

Popular brands

Pioneer AVIC-S1, User Manual

Search results

Summary of Contents for AVIC-S1

Reviews:

Related manuals for AVIC-S1

Brands by name

Popular brands