Pioneer AVIC-S1 User Manual Download Page 27

Page: 27 / 124

User's manual AVIC-S1

Navigation

- 25 -

ESTINATION

window

In the D

ESTINATION

window you may enter a destination,

process routes or view the map.

Note: When you turn your device on it shows the screen which
was displayed when it was turned off.

4.3

Entering a destination

Basis of navigation

This section describes the various possibilities of entering,
selecting and managing a destination in AVIC-S1.
The view of the map during navigation is described in chapter
"Starting navigation" On page 60.

Note: The settings that are specified in the settings window
R

OUTE

REFERENCES

are taken into consideration when calculating

the route for the entered destination.

For further information, please refer to chapter "Configuring

AVIC-S1" on page 91.

Summary of Contents for AVIC-S1





























































































































Search results

Summary of Contents for AVIC-S1

Reviews:

Related manuals for AVIC-S1

Brands by name

Popular brands

Pioneer AVIC-S1, User Manual

Search results

Summary of Contents for AVIC-S1

Reviews:

Related manuals for AVIC-S1

Brands by name

Popular brands