Pioneer AVIC-S1 User Manual Download Page 82

Page: 82 / 124

User's manual AVIC-S1

- 80 -

Simulation

The R

OUTE

REFERENCES

window opens.

Carry out the desired changes to the routing options.

Detailed information regarding establishing the routing
options can be found in chapter "Configuring AVIC-S1" on

page 91.

Tap on the Recalculate button.
The route is then recalculated. Navigation then continues
whilst taking into account the new route preferences.

6.5

Simulation

Overview

Once you have planned and calculated a route you can start a
simulated navigation. For more information, refer to chapter

"Simulating a route" on page 60.

Note: You do not need GPS reception in order to simulate a

route.
Only routes of max. 100 km in length can be simulated.

Summary of Contents for AVIC-S1





























































































































Search results

Summary of Contents for AVIC-S1

Reviews:

Related manuals for AVIC-S1

Brands by name

Popular brands

Pioneer AVIC-S1, User Manual

Search results

Summary of Contents for AVIC-S1

Reviews:

Related manuals for AVIC-S1

Brands by name

Popular brands