Pioneer AVIC-S1 User Manual Download Page 10 | Manualshive

Page: 10 / 124

background image

User's manual AVIC-S1

- 8 -

Legal notice

Term

Use

Select

Use the scrolling wheel to select an element
so that it has the focus.

Press

Is used only for buttons and the scrolling
wheel.

1.2

Legal notice

1.2.1

Liability

Limitation of liability

The software and the manual are subject to change without

notice. Pioneer may not be liable for the correctness of the
information contained in this manual nor for damages resulting

from the use of this manual.
To improve the quality of our products and our services, we

appreciate all suggestions for improvement and all error notices.

1.2.2

Trademarks

Registered
trademarks

All brands and trademarks mentioned in this document are
possibly registered by third party and subject to the current

legislation and to the rights of their respective owners without
reservation. All mentioned names of products, societies, or

brands may be registered trademarks of their respective owners.
Every right that is not explicitly accorded is reserved.
The absence of an explicit labelling of registered trademarks does
not allow the conclusion that this brand was not subject to the
rights of third party.

Ù

Windows and ActiveSync are registered trademarks of the
Microsoft Corporation.

1.3

Support

Please contact the dealer or distributor from where you purchased this unit for after-sales
service (including warranty conditions) or any other information. In case the necessary

information is not available, please visit the following site:

«
...
8
9
10
11
12
...
»

Summary of Contents for AVIC-S1





























































































































Reviews:

No comments

Related manuals for AVIC-S1

Brand: Medion Pages: 96

Brand: Discount Car Stereo Pages: 6

Brand: Revo Pages: 15

Stealthbox SB-D-DRNGO/10W0

Brand: JL Audio Pages: 3

Brand: Scottoiler Pages: 1

Brand: Bosch Pages: 252

Brand: Audi Pages: 28

KICKER 19119147

Brand: Stillwater Designs Pages: 8

Brand: VDO Pages: 36

Brand: Venturer Pages: 20

Brand: Komet Pages: 65

Brand: Pyle Pages: 35

Chrysler Radio Navigation System RB4

Brand: Harman Pages: 86

Brand: Xomax Pages: 19

K.I.S - PFU-KIS

Brand: DANHYDRA Pages: 8

Brand: Car Solutions Pages: 47

Brand: Metra Electronics Pages: 8

Brand: Metra Electronics Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands