Pioneer AVIC-S1 User Manual Download Page 14

Page: 14 / 124

User's manual AVIC-S1

- 12 -

Power supply and charging the battery

2.1

Power supply and charging the battery

Having unpacked your navigation system the battery will be flat.

You must connect the device to an external power source in order
to charge the battery.

Once you have connected the device to an external power supply,

you can use it even if the battery is flat.

2.1.1

At home

Connect the smaller end of the 220 V charging cable to the

respective jack on the bottom of the navigation device.

Insert the other plug in a socket.
The diode for the charging status of the battery to the left of

the screen lights up orange.

2.1.2

In the car

Install the cradle as described in its manual.

Place the device in the cradle.
The diode for the charging status of the battery to the left of

the screen lights up orange.

2.1.3

End of charging procedure

As soon as the diode lights up green, the battery is completely
charged.

Caution: Prior to the first full charge, do not disconnect the

device from the power supply until it has charged completely!
Otherwise you could damage the battery.

Summary of Contents for AVIC-S1





























































































































Search results

Summary of Contents for AVIC-S1

Reviews:

Related manuals for AVIC-S1

Brands by name

Popular brands

Pioneer AVIC-S1, User Manual

Search results

Summary of Contents for AVIC-S1

Reviews:

Related manuals for AVIC-S1

Brands by name

Popular brands