IntelliTouch
®
Control System User’s Guide
56
IntelliFlo VF 3050, VS 3050, VS+SVRS, VSF+SVRS Pump Setup
Setting up IntelliFlo
The IntelliFlo pump can be remotely controlled by an IntelliTouch system using the two-wire 50 foot
RS-485 communication cable (P/N 350122). IntelliFlo operations can be adjusted from the IntelliTouch
indoor control panel or MobileTouch wireless remote. For more information refer to the following
manuals: IntelliFlo VF 3050 (P/N 350075), IntelliFlo VS 3050 (P/N 357269), IntelliFlo VSF+SVRS
(P/N 351420)
How many pumps will IntelliTouch support?
IntelliTouch can support up to eight IntelliFlo VF and four IntelliFlo VS pumps in any combination with
up to eight GPMs or RPMs per pump. For example pumps can be connected to IntelliTouch as follows:
•
8 IntelliFlo VF
•
7 IntelliFlo VF + 1 IntelliFlo VS (or VS+SVRS or VSF +SVRS)
•
5 IntelliFlo VF + 3 IntelliFlo VS (or VS+SVRS or VSF +SVRS
•
4 IntelliFlo VF + 4 IntelliFlo VS (or VS+SVRS or VSF +SVRS (or only 4 IntelliFlo VS pumps)
Connecting power to an IntelliFlo pump
The IntelliFlo pump is designed to be permanently connected to its power source. Typically the pump
receives power directly from the circuit breaker. No contactor or motor starter is required. The drive
controls the starting and stopping of the pump. If the IntelliFlo pump is connected to an automation
system, such as the IntelliTouch automation system, the drive must be powered up to receive and
respond to the RS-485 serial communication from the automation system. However, the pump can be
operated in “stand-alone” mode, starting and stopping when power is applied or removed. When the
drive powers up it will return to the mode and run status that it was in when power was removed. This
setup maybe appropriate if you need to use existing relays or timers.
Assigning an IntelliFlo VF 3050 pump address
Before assigning a pump address in the IntelliTouch indoor control panel, first set the
address
on the pump itself.
If there is only one pump, it is always seen as pump #1 by
IntelliTouch. In this case you do not need to set the pump address. When using multiple
IntelliFlo pumps with IntelliTouch you need to assign an address to each pump. The
address can be set to #1, #2, #3, #4, #5, #6, #7, or #,8. The address set at the pump must
match the IntelliFlo pump number selected in the IntelliTouch indoor control panel.
Note:
IntelliFlo VF 3050 pumps cannot be connected in series with other pumps.
Check valves must be used when a pump is used in parallel with other pumps.
To assign an IntelliFlo VF 3050 pump address:
1. Press the
Start/Stop
button to stop the pump. Be sure that the green power LED is
on and the pump is stopped.
2. Press the
Menu
button.
3. Press the
Up and Down
arrow buttons to scroll through the menu items. Press the
Select
button to access the “Pool Data” menu.
4. Press the
Select
button to access the “Pump Address” setting.
5. Press the
Select
button to change the current pump address.
6. To enter the new address number, press the
Left
and
Right
arrows to select which
digit to modify, then use the
Up
and
Down
arrows to change the selected digit.
7. When you are done assigning the pump address number, press the
Enter
button to
save the changes. To cancel any changes, press the
Escape
button to exit edit mode without saving.
Filter
Vacuum
Back
Wash
Manual
Enter
Se
le
ct
Reset
Feature
2
Feature
1
Men
u
Es
ca
pe
On
Warn.
Alarm
IntelliFlo
®
MENU
12:15
Pool Data
Start
Stop
Filter
Vacuum
Back
Wash
Manual
Enter
Se
le
ct
Start
Stop
Reset
Feature
2
Feature
1
Menu
Es
ca
pe
On
Warn.
Alarm
IntelliFlo
®
Pool Data
12:01
Pump Address
1
Summary of Contents for INTELLITOUCH
Page 9: ...vii IntelliTouch Control System User s Guide BlankPage...
Page 126: ...NOTES...
Page 127: ...NOTES SAVE THESE INSTRUCTIONS...
