Panasonic S-ICX Technical Manual Download Page 261

Page: 261 / 327

Section 700 - Operation

Chapter 6. DSLT Features

S-ICX-50-700

S-ICX (International) issued October 2000

261

Hardware Requirements

•

N/A

Considerations

(Call Barring)

•

The same Walking TRS (Call Barring) COS code can be used on more than one extension.

•

Walking TRS (Call Barring) COS mode is kept until the user goes on-hook.

•

ARS and TRS (Call Barring) dialling privileges follow the Walking TRS (Call Barring) COS.

•

Before entering a new Walking TRS (Call Barring) COS code, you must first clear the existing
code.

•

When Walking TRS (Call Barring) COS is used, Wxxxx (where xxxx is the user’s extension
number) appears in Call Logging.

Summary of Contents for S-ICX








































































































































































































































































































































Search results

Summary of Contents for S-ICX

Reviews:

Related manuals for S-ICX

Brands by name

Popular brands

Panasonic S-ICX, Technical Manual

Search results

Summary of Contents for S-ICX

Reviews:

Related manuals for S-ICX

Brands by name

Popular brands