Panasonic S-ics Page 227 Technical Manual Download

Page: 227 / 327

Section 700 - Operation

Chapter 6. DSLT Features

S-ICX-64-700

S-ICX (International) issued April 2002

227

•

You can set Call Forwarding - All Calls while Call Forwarding - No Answer and/or Call

Forwarding - Busy are set. Cancelling one mode only affects that mode; however, the other

modes will remain set until cancelled individually.

•

An auto camp-on to a busy extension will forward to the Call Forward No Answer destination. A

manual camp-on to a busy extension will not forward.

•

If Call Forwarding No Answer and DND are both set, calls immediately forward to the Call

Forward No Answer destination.

•

You can cancel both Call Forwarding and DND by entering

7 * *

Call Hold

Description

The system provides the following types of Call Hold:

•

System Hold

•

Floating Hold

•

Exclusive Hold

•

Broker’s Hold

•

Call Park (Station)

System Hold

You can place either an outside or intercom call on System Hold. You can retrieve a call placed on

System Hold from any extension that has a line appearance for the held call.

Operation

To place a call on System Hold:

To retrieve a call placed on System Hold:

To retrieve a held call on a specific exchange line:

Action

Result

1. While on a call, press the

HOLD

key.

Intercom dial tone

Action

Result

1. Press the

HOLD

key.

Intercom dial tone

Action

Result

1. Lift the handset or press the

ON/OFF

key.

Intercom dial tone

Summary of Contents for S-ics








































































































































































































































































































































Search results

Summary of Contents for S-ics

Reviews:

Related manuals for S-ics

Brands by name

Popular brands

Panasonic S-ics, Technical Manual

Search results

Summary of Contents for S-ics

Reviews:

Related manuals for S-ics

Brands by name

Popular brands