manualshive.com logo in svg

Panasonic S-ics, Technical Manual

The Panasonic S-ics Technical Manual is a comprehensive guide for users looking to optimize their experience with this cutting-edge product. This invaluable resource can be easily downloaded for free from manualshive.com, providing users with detailed instructions and troubleshooting assistance for utilizing all features of the Panasonic S-ics.

Share
Download
background image

266

S-ICX (International) issued April 2002

S-ICX-64-700

Chapter 7. SLT Features

Section 700 - Operation

To cancel an Absence Message

Hardware Requirements

•

N/A

Related Programming

•

FF1 (System): Extension Class of Service Setting 

•

FF3 (Extension): Extension Class of Service Assignment 

•

FF8 (Maintenance): Absence Messages

Considerations

•

Calling parties without a display get a busy signal, rather than the Absence Message.

•

Regardless of setting an Absence Message on a DDI/DIL extension, DDI/DIL calls are routed 

according to the trunk ringing setting. 

•

An absence message may also be cancelled by dialling 

7**

. This cancels Do-Not-Disturb (DND) 

and Call Forwarding-All Calls as well.

Account Codes

Description

You can assign account codes to clients to facilitate billing and to track call dates and times, numbers 

called, and outside line numbers used. This information is printed for each account on the Call 

Logging record.

In addition verified account codes may be used to change the Toll Restriction Service (TRS) (Call 

Barring) level to allow calls to numbers otherwise restricted.

Account codes may be either forced or unforced (voluntary) and either verified or unverified.

This feature works with Call Logging. Before making an outgoing call, a station user can silently 

enter an accounting or client billing code. Then later, the Call Logging reports will show the Code 

dialled for each call, and even sort the report by these Codes.

There are two different types of account codes: Non-Verified and Verified Account Codes. Prior to 

Version 5.0, the maximum amount of account code numbers for both types could range from 1-10 

digits. Beginning with Version 5.0, a second mode has been added that allows the user to set the 

maximum amount of account code numbers from 1-4 digits. An account code error will occur when 

more than the maximum number of digits are entered.

Action

Result

1.   Lift the handset.

Intercom dial tone

2.   Enter the Absence Message code (default = 

729

). 

3.   Flash the hookswitch.

4.   Replace the handset.

Summary of Contents for S-ics








































































































































































































































































































































Reviews:

No comments

Related manuals for S-ics

D-Link i2eye DVC-1000 Manual preview
i2eye DVC-1000
Brand: D-Link Pages: 67
Uniden DECT1560 Series User Manual preview
DECT1560 Series
Brand: Uniden Pages: 64
C&TT WCS-211 User Manual preview
WCS-211
Brand: C&TT Pages: 19
invotel SX8500 User Manual preview
SX8500
Brand: invotel Pages: 6
Uniden DCT 748 Series Owner'S Manual preview
DCT 748 Series
Brand: Uniden Pages: 84
Ole M182 User Manual preview
M182
Brand: Ole Pages: 35
info-hold MP-3000 M Installation Manual preview
MP-3000 M
Brand: info-hold Pages: 2
Karel MS128 Easy To Use Owner'S Manual preview
MS128
Brand: Karel Pages: 80
Uniden CXAI 5198 SERIES Owner'S Manual preview
CXAI 5198 SERIES
Brand: Uniden Pages: 68
ONE.TEL Magma 110 User Manual preview
Magma 110
Brand: ONE.TEL Pages: 47
Inovonics EN2221S-60 Installation And Operation Manual preview
EN2221S-60
Brand: Inovonics Pages: 5
3SIXT SNAP STICK User Manual preview
SNAP STICK
Brand: 3SIXT Pages: 6
TechMatte amFilm GLS2 Installation Manual preview
amFilm GLS2
Brand: TechMatte Pages: 2
Zte WP651 User Manual preview
WP651
Brand: Zte Pages: 19
Panasonic KX-TCD515HK Specifications preview
KX-TCD515HK
Brand: Panasonic Pages: 2
Panasonic KX-TCD505HK Specifications preview
KX-TCD505HK
Brand: Panasonic Pages: 2
Panasonic KX-TCD430HK Specifications preview
KX-TCD430HK
Brand: Panasonic Pages: 2
Panasonic KX-TCD300HK Specifications preview
KX-TCD300HK
Brand: Panasonic Pages: 2

Brands by name

Popular brands

Load more brands