Panasonic S-ics Technical Manual Download

Page: 307 / 327

Section 700 - Operation

S-ICX-64-700

S-ICX (International) issued September 2001

307

Speed Dial Linking
Speed Dial Name Assignments

This feature is available only when using alphanu-
meric telephones.

Station Lockout

Step Call (Reset Call)

Timed Reminder Call

Trunk (Exchange Line) Access

Trunk (Exchange Line) Key Access

Depends on the key phone, and whether the maximum
exchanges available to assign FF keys are different.

Direct (Exchange Line) Access
MCO Line Preference
MCO Trunk (Exchange Line) Access

Trunk (Exchange Line) Queuing

Universal Night Answer to Page

Volume Control

A-series telephones have a slide switch. The SBS/VB-
9 telephone has Volume Up/Down key.

Walking TRS (Call Bearing) Class of Service

Zip Mode

Feature

Differences for SBS/VB-9 A-Series Telephones

Summary of Contents for S-ics








































































































































































































































































































































Search results

Summary of Contents for S-ics

Reviews:

Related manuals for S-ics

Brands by name

Popular brands

Panasonic S-ics, Technical Manual

Search results

Summary of Contents for S-ics

Reviews:

Related manuals for S-ics

Brands by name

Popular brands