Panasonic S-ics Page 176 Technical Manual Download

Page: 176 / 327

176

S-ICX (International) issued April 2002

S-ICX-64-700

Chapter 5. Key Telephone Features

Section 700 - Operation

Operation

To put a call on speaker using the Offhook Monitor:

Hardware Requirements

•

N/A

Considerations

•

Offhook Monitor is available on 44-Series phones only.

•

Offhook Monitor can be disabled system-wide.

Offhook Signalling

Description

Offhook Signalling sends a tone to a busy extension to indicate that another trunk call has arrived or a

call is camped-on.

Operation

After receiving an offhook signal during a call:

Note:

For details about handling multiple calls, see “Call Hold” on page 132.

Hardware Requirements

•

N/A

Considerations

•

The trunk call type may be multiple ring, direct, BLF Ring, or camp-on.

•

The System does not send the offhook signal under the following conditions:

• During a conference call
• During an OHVA or Busy override

Action

Result

1. During a handset call, press the

ON/OFF

key.

• Other party is audible through speaker

and handset

• Phone’s microphone is mute

2. To take a caller off speaker (disable Offhook Monitor) but

continue the call via the handset, press the

ON/OFF

key.

Action

Result

1. Press the

HOLD

key.

First call on hold

2. Press the flashing FF key for the trunk of the incoming call.

Summary of Contents for S-ics








































































































































































































































































































































Search results

Summary of Contents for S-ics

Reviews:

Related manuals for S-ics

Brands by name

Popular brands

Panasonic S-ics, Technical Manual

Search results

Summary of Contents for S-ics

Reviews:

Related manuals for S-ics

Brands by name

Popular brands