Panasonic S-ics Technical Manual Download

Page: 84 / 327

S-ICX (International) issued April 2002

S-ICX-64-700

Chapter 4. User Maintenance

Section 700 - Operation

Hardware Requirements

•

N/A

Considerations

•

N/A

Set Caller ID Logging Extensions

Description

You can assign Caller ID Call Logging to extensions. The system is limited to 20 call logging

extensions per cabinet as follows:

6. Dial the extension number.

7. Press the

HOLD

key.

Enter CODE

displays

8. Enter the destination extension.

9. Press the

HOLD

key to store the entry.

Next extension number displays

10. To set Call Forward No Answer destinations for additional

extensions, press the volume up and down key or press the

HOLD

key to move to the desired Extension.

11. Repeat steps 9-11 until all extension are entered.

12. Press the MEMORY key to exit the entry mode.

13. To return to the top menu level (

), press the

PROG

key.

OR...

To exit the User Maintenance mode, press the

ON/OFF

key.

81-

User MAINT

displays

OR...

ON/OFF

LED goes off

Number of Cabinets

Total Number of

Call Log Extensions

100

120

Action

Result

Summary of Contents for S-ics








































































































































































































































































































































Search results

Summary of Contents for S-ics

Reviews:

Related manuals for S-ics

Brands by name

Popular brands

Panasonic S-ics, Technical Manual

Search results

Summary of Contents for S-ics

Reviews:

Related manuals for S-ics

Brands by name

Popular brands