Panasonic S-ics Technical Manual Download

Page: 101 / 327

Section 700 - Operation

Chapter 4. User Maintenance

S-ICX-64-700

S-ICX (International) issued April 2002

101

5. Press the

HOLD

key.

Mode Special Day

displays

6. Press the

HOLD

key.

1000

:MMDD

Special Day 01

displays

7. Enter

the date by month (two characters) and day (two char-

acters) for the Special Day 1.

Note:

To clear an entry or existing data, press the FL/R key.

8. Press the

HOLD

key.

1001

:HHMM

S Day 01-1 Start

displays

9. Enter the start time in hours (two characters) and minutes

(two characters) for mode 1.

Note:

To clear an entry or existing data, press the FL/R key.

10. Press the

HOLD

key.

1002

S Day 01-1 Mode

displays

11. Enter the desired mode for Special Day ( (

- None,

Day 1,

- Day 2,

- Night,

- Night(1),

- Night (2)).

Note:

To clear an entry or existing data, press the FL/R

key.

12. Press the

HOLD

key.

Next Special Day mode displays

13. To set additional Special Day modes, press the volume up

or down key or press the

HOLD

key to move to the desired

mode.

14. Repeat steps 7-13 until all Special Day modes are set. (Up

to 20 special days may be entered.)

Note

: The entry positions are listed in Table 13.

15. Press the MEMORY key to exit the entry mode.

Mode Special Day

displays

16. To return to the top menu level (

), press the

PROG

key.

OR...

To exit the User Maintenance mode, press the

ON/OFF

key.

81-

User MAINT

displays

OR...

ON/OFF

LED goes off

Action

Result

Summary of Contents for S-ics








































































































































































































































































































































Search results

Summary of Contents for S-ics

Reviews:

Related manuals for S-ics

Brands by name

Popular brands

Panasonic S-ics, Technical Manual

Search results

Summary of Contents for S-ics

Reviews:

Related manuals for S-ics

Brands by name

Popular brands