Panasonic S-ics Technical Manual Download

Page: 170 / 327

170

S-ICX (International) issued April 2002

S-ICX-64-700

Chapter 5. Key Telephone Features

Section 700 - Operation

Four DSS/BLF modes are available as follows:

Operation

To assign a DSS/BLF key

To make an intercom call using the DSS/BLF key:

To pick up a call on a DSS/BLF key:

Hardware Requirements

•

N/A

DSS/BLF Type

FF Key

Entry

BLF LED

Indication

Extension

Call

Pickup

Ring

(Immed.)

Ring

(Delayed)

Voice Mail

Transfer

DSS Only (No
Pick Up/No Ring)

(9 + Ext #)

Yes

DSS/BLF
Immediate Ring

(81 + Ext #)

Yes

DSS/BLF Delayed
Ring

(82 + Ext #)

Yes

DSS/BLF No Ring

(83 + Ext #)

Yes

Action

Result

1. Press the

PROG

key.

2. Press the FF key to be assigned the DSS/BLF appearance.

3. Press the

REDIAL

key.

4. Enter the code for the desired DSS/BLF mode as follows:

9+ Ext #

---- DSS Mode Only

81+ Ext #

--- DSS/BLF Immediate Ring

82 + Ext #

-- DSS/BLF Delayed Ring

83 + Ext #

-- DSS/BLF No Ring

5. Press the

HOLD

key.

Action

Result

1. Press the flashing DSS/BLF key.

Action

Result

1. Go off-hook or press the flashing DSS/BLF key.

Summary of Contents for S-ics








































































































































































































































































































































Search results

Summary of Contents for S-ics

Reviews:

Related manuals for S-ics

Brands by name

Popular brands

Panasonic S-ics, Technical Manual

Search results

Summary of Contents for S-ics

Reviews:

Related manuals for S-ics

Brands by name

Popular brands