Panasonic S-ics Technical Manual Download

Page: 276 / 327

276

S-ICX (International) issued April 2002

S-ICX-64-700

Chapter 7. SLT Features

Section 700 - Operation

Operation

To retrieve a call from Floating Hold:

Hardware Requirements

•

N/A

•

Considerations

•

The number of floating hold orbits available may very depending on the Station Park/Floating

Hold Pickup setting (FF1-0-02-0025). The station park pickup access code can set to

(default). The “

” access code operates as follows:

Exclusive Hold

With Exclusive Hold, only the extension that held the call can retrieve it. Exclusive Hold can be used

to hold trunk calls and extension calls.

Operation

To place a call on Exclusive Hold:

To retrieve a call from Exclusive Hold:

Hardware Requirements

•

N/A

Action

Result

1. Lift the handset.

2. Enter the Floating Hold Answer feature access code

(default =

)

3. Enter the

Floating Hold Orbit number

01-96

(CPC-HS/HM)

01-09

(CPC-HS/HM) (See considerations below.)

System Size

Virtual Line Number and Operation

01-09 Floating Hold pick up
10-96: Station Park Hold pick up purpose

Action

Result

1. While on a call, hookflash.

Intercom dial tone

Action

Result

1. If onhook, lift the handset.

2. Hookflash.

Summary of Contents for S-ics








































































































































































































































































































































Search results

Summary of Contents for S-ics

Reviews:

Related manuals for S-ics

Brands by name

Popular brands

Panasonic S-ics, Technical Manual

Search results

Summary of Contents for S-ics

Reviews:

Related manuals for S-ics

Brands by name

Popular brands