Panasonic S-ics Technical Manual Download

Page: 219 / 327

Section 700 - Operation

Chapter 6. DSLT Features

S-ICX-64-700

S-ICX (International) issued April 2002

219

Operation

To make an outside call that requires an account code:

Hardware Requirements

•

An Call Logging printer or external call accounting system is required to collect account code
records.

Considerations

•

Account codes are not available during conversation recording mode for the Built-In Voice Mail.

•

Even though up to 10 digits may be entered, the system verifies the ID based on the first 4 digits
only.

•

Account codes will be cancelled after using trunk queuing.

•

Account Codes interact with TRS (Call Barring) as shown in the following table:

Attendant Group Calls

Description

You can call the attendant group from any extension by dialling the designated attendant number.

Action

Result

1. Lift the handset or press the

ON/OFF

key.

Intercom dial tone

2. Enter the Verified Account ID code (default =

3. Enter the Account Code (10 digits).

4. Press a vacant Exchange Line key or enter an exchange line

access code (default = 9 or 81-84).

5. Dial the phone number.

Forced or Not Forced

Verified or

Non-Verified

TRS (Call Barring) Class

No Account Entry

Account Entry

Not Forced

Non-Verified

Extension Port Based TRS

Class

Extension Port Based TRS

Class

Verified

Account Code Based TRS

Class

Forced

Non-Verified

TRS Class for Forced

Account Code

(FF1 0 19 0001)

Extension Port Based TRS

Class

Verified

Account Code Based TRS

Class

Summary of Contents for S-ics








































































































































































































































































































































Search results

Summary of Contents for S-ics

Reviews:

Related manuals for S-ics

Brands by name

Popular brands

Panasonic S-ics, Technical Manual

Search results

Summary of Contents for S-ics

Reviews:

Related manuals for S-ics

Brands by name

Popular brands