Panasonic S-ics Technical Manual Download

Page: 189 / 327

Section 700 - Operation

Chapter 5. Key Telephone Features

S-ICX-64-700

S-ICX (International) issued April 2002

189

Considerations

•

PSD number can be dialled from One-Touch keys. (For additional information, see “One-Touch

Keys” on page 179.)

•

Storing a new number erases any previously stored data.

•

If the called party’s number and name are stored in the PSD code, that information appears on the
display when you use the speed dial code.

•

Speed dial numbers can contain up to 24 characters. The following table reflects which keys to

use.

Indicates that the digits that follow are either a feature access code or an extension

number. (Not needed if your System is set for Intercom Level.) See

Note

below.

** Indicates that the digits that follow are for an outside number and the System should

seize the next available exchange line when dialling. (Not needed if your System is set

for trunk level.) See

Note

below.

*** Indicates that the enclosed digits should not be displayed during dialling. Must precede

and follow the digits that you do not want displayed.

Example: MEMORY *2 555-

4143 MEMORY *2.

Note:

The System has two levels - Trunk Level and Intercom Level. If set at Trunk Level

(default), you must enter the code for Intercom Level when programming a feature access code

or extension number for speed dialling. If the System is set at Intercom Level, you must enter the

MCO Code when programming an outside number for speed dialling.

System Speed Dial

You can store frequently called numbers using the SSD feature. Either 80 or 800 SSD numbers can be

programmed, depending on how the System is configured. In an 80 SSD-number system, the SSD

numbers are stored in bins

. In 800 SSD-number systems, the SSD numbers are stored in bins

000

799

To indicate. . .

Enter/Press

Shown on Display?

Digit or character

yes (unless preceded by

MEMORY * 2

- see

below)

Intercom Level *

MEMORY * #

MCO Code

MEMORY * 0

MCO Code 81**

MEMORY * 71

MCO Code 82**

MEMORY * 72

MCO Code 83**

MEMORY * 73

MCO Code 84**

MEMORY * 74

Pause

FL/R

DP - DTMF Code

MEMORY * *

SSD Code

MEMORY NN(N)

Hyphen (-)

PROG

Display Number (Start / Stop)
***

MEMORY * 2

DTMF Conversion After the
Other Party Answers

MEMORY * 3

Summary of Contents for S-ics








































































































































































































































































































































Search results

Summary of Contents for S-ics

Reviews:

Related manuals for S-ics

Brands by name

Popular brands

Panasonic S-ics, Technical Manual

Search results

Summary of Contents for S-ics

Reviews:

Related manuals for S-ics

Brands by name

Popular brands