manualshive.com logo in svg

otometrics MADSEN OTOflex 100, Reference Manual

Share
Download
otometrics MADSEN OTOflex 100 Reference Manual Download Page 55

7.4.3

Fitting the probe in the patient’s ear

Note

•

This procedure does not apply to screening eartips, which should simply be held firmly against the ear

canal opening of the patient.

Warning

•

Be careful not to insert the probe too far into the ear canal of premature babies and newborns.

Warning

•

The eartip can be used for both ears. If you suspect infection in one ear, exchange the eartip and clean

the probe tip before you continue testing on the other ear.

Caution

•

Always use a suitably sized eartip. Using a probe with an unsuitably sized eartip or applying excessive

force may cause unnecessary discomfort to the patient.

Note

•

Because infants’ ear canals are very soft, they are easily pressed out of shape.

If this happens, wait until the ear canal returns to its original shape. Release the pinna and try again. Gently mas-
saging the area may help opening the ear canal.

1. Fit the eartip on the probe.

2. To stabilize the probe and to avoid blocking the probe against the ear canal of the patient, grasp the pinna and gently

pull the pinna back and slightly away from the patient's head.

–

For adults: pull the pinna upwards and back.

–

For infants and children: pull the pinna downwards and back.

3. Insert the probe in the patient's ear canal, twisting the eartip slightly as you insert it.

4. Make sure that the eartip fits well. Any leakage may interrupt the test.

To compensate for spontaneous movements of the patient’s
head:

–

Place the probe cable behind the patient’s neck.

–

To keep the cable in place, place a weighted shoulder
harness over the cable, from front to back of the patient,
across the shoulder opposite the ear being tested.

–

Make sure that the cable is not drawn tight, as this may
result in the probe being pulled out of position.

Otometrics - MADSEN OTOflex 100

55

7 Preparing for testing

Summary of Contents for MADSEN OTOflex 100

















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands